How to cut rounded outside corners with a miter saw.
Want to know how to cut a quarter turn without a miter saw? If so, then you've come to the right place. Rounded corners are best cut with a miter saw. However, that doesn't mean you can't cut it if you don't have one.
In this article I will teach you how to cut a quarter turn without a miter saw. I will also teach you what tools you need to cut rounded corners. You will also learn how to do it correctly and efficiently.
So without further ado, let's waste some more time titrating and learn how to cut a quarter turn without a miter saw.
Just like other DIY projects, you need essential tools to cut round shapes. I will mention all necessary for this project. However, you must use these tools according to the method you are using to cut a quarter turn without a miter saw.
- a tape measure
- carpenter's pencil
- A high quality speed square
- A square box
- Multi Angle Miter Cutter
- A circular saw (if you don't want to use a miter box)
- A hacksaw or handsaw (if you can't afford a power tool)
- Clamps (to hold the part)
At what angle do I cut a quarter turn?
Your quarter round angles are based on your needs and requirements. However, most projects require 90 degree connections. For such an angle, you need to cut two pieces at 45 degrees. I already covered how to cut a 45 degree angle without a miter saw in my other article.
If you want more details, you can read my article. Anyway, back to the point, you need to make a proper 90 degree angle when combining the two pieces of wood.
Always remember that angle measurement is extremely important in woodworking. Even if your cut pieces are off by a few degrees, it will ruin your entire project. This masalah is great not only for quarter turns, but also for finishing and shaping crowns. So you have to be extremely careful when making your 45 degree cuts.
Note: In this tutorial we will try to learn how to cut a quarter turn without a hacksaw in four different ways. You can use any of the techniques mentioned to efficiently cut round or round pieces.
1. Cut round pieces with a handsaw
The first technique I'm going to teach you is using a handsaw. It's one of the easiest and most effective ways to cut trim pieces or quarter circles. If you are a total beginner, this technique will take some practice to master.
You can also use a hacksaw for better results. Quarter rounds are available in different sizes. More commonly, 8 foot and 16 foot lengths are available at most hardware stores.
I recommend finding the right length for your needs. This makes the job easier and prevents you from assembling multiple pieces that could spoil the perfection of the project.
Anyway, here's the correct way to cut a quarter turn with a handsaw.
Get the right size round tiles for your walls.
Take your tape measure and carefully measure the length of the baseboard.
Using your tape measure, mark a line on the amount of wood you need.
Use an angle finder or speed square to correctly mark the 90 degree and 45 degree angles.
Lay the round piece on the ground with the flat side facing down.
Grab your hand saw or coping saw and start cutting the wood along the line.
Be very careful when cutting and don't rush into anything. Because if you hurry, you're likely to miss the line.
As I mentioned before, even a small mistake leads to a complete disaster. Your piece will look terrible because there will be a significant gap between the two pieces.
Therefore, when cutting the pieces of wood, you need to put the saw on the pencil line and carefully cut.
If you don't have a handsaw and still want to cut or shape, here's another technique you can use.
2. Cut round parts with a multi-angle miter cutter
Another amazing technique that can help you cut or trim the frame more easily. This method is a bit easier compared to the previous technique. It's because the
Multi Angle Miter Cutter
it is relatively easier to use.
Multi Angle Miter Cutter Hand Tools 45-135 Degree Adjustable Angle Scissors Cutting Tools
- Designed for cutting tile trim, PVC pipe, quarter rounds, tack strips and other lightweight materials.
- Suitable for cutting PVC or PE plastic pipe, wooden strip, wire, etc. can't cut hard wood.
- Multi-degree: The sharp blades have a cutting angle of 45, 60, 75, 90, 105, 120, 135 degrees,
- HIGH QUALITY: Sturdy steel frame with plastic cover handle for convenient diagonal cutting
- Non-slip ergonomic handle, save time and labor, easy to cut.
superbcutter.com participates in the Amazon Services LLC Affiliate Program, an affiliate advertising program designed to allow websites to earn advertising fees by advertising and linking to amazon.com.
In addition, it has different angles that allow you to make 45 degree cuts more easily. So here's the right way to cut rounded corners with multi-angle cutting scissors.
Take the necessary measurements according to your needs
Place the quarter-turn wood in the jaws of the angle cutter with the flat side facing away from you.
Make sure you make the correct cut using the guide and angled line on the tool.
Make the cut by applying pressure to the knife.
After completing all of the above steps you will have a nice piece of the rounded corner.
But that's not all, because there is another method to cut the pieces of wood in a quarter turn.
3. Use a miter box to cut the round corner pieces
The next method I'm going to teach you is quite interesting. You can use a simple miter box to cut the round pieces. This technique doesn't require much skill as you just need to know how to properly use a miter box.
Here is the correct way that can help you cut the quarter turn pieces with the help of a miter box. You can easily cut at a 45 degree angle with this technique. In addition to round quarters, the miter box can help you cut baseboard corners, trim, and other types of parts.
Here's the correct way to cut quarter turns with a miter box or hand miter saw.
Measure the piece perfectly with a tape measure and a thin pencil. Carefully draw a line on one end of the wood and move to the other side.
Place the workpiece in the miter box.
Place the saw blade/saw in the 45 degree angle slot
Begin cutting the wood to the exact length. Use the pencil mark line as a guide to trim the corners cleanly.
4. Use a circular saw to cut the rounded corner
The next technique that can help you cut the quarter round or baseboard piece is to use a circular saw. Now, some of you may not agree, but a circular saw can help you in many situations.
I know the quarter turns are very small and unlike the baseboard you will have a little trouble cutting with your circular saw.
However, it is still possible and I will teach you exactly how to do it without any problems. So, without further ado, let's look at how you can make quarter turn 45 degree angle cuts with a circular saw.
Measure the length of wood you need with a tape measure and mark the exact line on one side of the quarter turn.
Use a clamp to hold the frame in place, otherwise it will move and could affect accuracy.
Match the correct blade to your circular saw. You can use any exotic wood blade with 60 or more teeth.
Set the blade depth correctly. Make sure the blade is titrated more than 1/4 inch deeper than the quarter round thickness.
Start cutting the frame. With straight cuts there should be no complication. That's because straight cuts are extremely easy and almost anyone can easily cut a straight piece of wood.
However, if you're making slanted cuts, you can use your speed square to help your blade. As I mentioned earlier, the angle is only useful for angled cuts, and it's not required for straight cuts.
last minute thoughts
If you don't have a miter saw and still want to cut a quarter turn, this guide article will help you. I have mentioned several ways that can help you complete the project easily. With the above information you can easily cut not only moldings, but also baseboards and other types of wood.
With the tool mentioned above, you can master even difficult corner angles like a pro. In this article, I have explained 4 different ways that you can use to get the job done completely and cover the space between the floor and the walls. With the right measurements, you can simply place a piece on each person and edge of the wall.
I hope you enjoyed reading the article, please share with your friends and family. You can also contribute to the article through the comments section.
- UnderstandingMadeira: A handbook for craftsmenMadeiraTechnology
- Install synthetic crownmolding
What angle do you cut trim for outside corners? ›
To form an outside corner joint, set the saw blade at 45 degrees to the left; cut the first length of molding. Rotate saw to 45 degrees to the right and cut the second mating molding piece. For an inside corner joint, square-cut the first piece of molding and butt it tight into corner.What angle should an outside corner miter saw be? ›
For example assuming that your wall isn't square (because most aren't), your inside corner is 88 degrees. 88 divided by 2 is 44. Set your miter saw to 44 degrees and make your cut. Now for the outside corner.How do you cut the trim for a 45 degree corner outside? ›
- With a measuring tape, measure from the outside edge of the corner, back along the wall to the end. ...
- Place trim molding on a miter saw in the position it will go when installed.
- Put the first end of the molding under the blade.
- Turn the blade to 45 degrees outward. ...
- Cut the trim.
Outside Corner / 90° or 135°What is 31.6 on a miter saw for? ›
31.6 degrees, which is the standard miter angle for certain compound rafter cuts in many common stick home roof construction situations. Because it is so common, most compound miter saws feature several quick settings like this, to save time and ensure repeatability over dozens or hundreds of cuts.What is 135 degrees on a miter saw? ›
A 135 degree angle is an OBTUSE angle. The miter for this corner is 67 1/2 degrees. That's easy to cut on your miter saw. Just set the saw at 22 1/2!How do you get baseboards to meet in the corner? ›
- Mark Direction of Cut on First Baseboard. Press the squared-off end of the first baseboard piece tight into the corner along the floor. ...
- Set the Saw Angle. ...
- Cut the First Piece. ...
- Clean up the Cut Edges. ...
- Reverse the Saw Blade. ...
- Cut the Adjoining Baseboard. ...
- Mark the Straight Cuts. ...
- Test-Fit the Baseboards.
When the right angle is divided into two equal parts each angle measures 45°. A 45-degree angle is an acute angle. It is half of the right angle or a 90-degree angle. Take a look at the image of the 45-degree angle.How do you finish outside corners of walls? ›
- Start with a corner that's straight and secure. ...
- The adhesive coat must be thin. ...
- Use finger pressure. ...
- Gently wipe the edges. ...
- Mix the mud between coats. ...
- Smooth the first coat. ...
- Fill the gaps with your final coat. ...
- Skim and sand.
Doesn't matter a bit. The main time you need to think about how corners work is when the backing studs are different width. (If, for instance, you only have 1" of stud to attach to on one side of a corner, and 3-1/2" on the other side of the corner, you'll want to have the drywall sitting fully on that inch.)
Can drywall tape be used on outside corners? ›
Metal-reinforced drywall tape can be folded lengthwise for use along inside or outside wall corners. 8. Rigid, pre-formed drywall corners can also be used at inside wall corners.Do you have to use corner bead on drywall? ›
Corner bead is typically only used on outside corners because it's vulnerable to wear and tear. Although corner beads are used on inside corners, they aren't necessary, since a simple paper tape installation will suffice.